Construction & Home ImprovementLast reviewed: November 2026

French Drain Calculator

A French drain calculator designs a subsurface drain to move groundwater away from your foundation. Enter the trench length, width and depth, and it works out excavation volume, washed-stone tonnage after subtracting pipe displacement, and the geotextile fabric needed to keep silt from clogging the drain.

Key facts:
  • Drain pipe holes must always face down.
  • A 50-ft trench (12 by 18 in) needs about 3.9 tons of washed stone.
  • Keep at least a 1% slope — 1 inch of fall per 8 feet.
  • Without geotextile fabric, silt can clog a drain in 2 to 5 years.

Loading calculator…

Share or Export Current Results

Share French Drain Calculator directly or copy link to clipboard

TwitterLinkedInFacebookWhatsApp

Calculation Formula & Mathematical Engine

Theoretical equation governing this computation.

Gravel_{tons} = \frac{(L \times W \times D - V_{pipe}) \times 1.10}{27} \times 1.35

Variable Definitions

Gravel_{tons}Washed angular drain rock tonnage (~1.35 tons/yd³)
V_{pipe}Pipe volume displacement subtracted from trench volume
FabricNon-woven geotextile wrapping cloth to prevent silt clogging

Step-by-Step Calculation Example

50-Foot French Drain Trench (12" Wide × 18" Deep)

Scenario: Designing a 50-foot residential foundation water mitigation trench with 4" perforated pipe.
Trench Length50 ft
Trench Width12 inches (1.0 ft)
Trench Depth18 inches (1.5 ft)
Pipe Size4-inch perforated PVC
Execution Steps
  1. 1Gross trench volume: 50 × 1.0 × 1.5 = 75 cu ft
  2. 2Pipe displacement: 50 × π × (4/24)² ≈ 4.36 cu ft
  3. 3Net gravel volume: 75 - 4.36 = 70.64 cu ft ÷ 27 × 1.10 = 2.88 cu yds
  4. 4Gravel weight: 2.88 × 1.35 = 3.89 tons of washed stone
  5. 5Fabric wrap perimeter: 1.0 + (2 × 1.5) + 1.0 overlap = 5.0 ft width × 50 ft length = 250 sq ft
Final Verified Output:3.9 Tons #57 Washed Drain Rock + 50ft 4" Perforated Pipe + 250 Sq Ft Geotextile Fabric

How to Install a French Drain

Follow these steps to get your result.

  1. 1Plan the drain route downhill to a safe outlet, allowing at least a 1% fall.
  2. 2Enter the trench length, width and depth to get the gravel tonnage and fabric area.
  3. 3Dig the trench — 12 inches wide and 18 inches deep is typical — and line it with non-woven geotextile fabric.
  4. 4Lay perforated pipe with the holes facing down, then backfill with washed #57 stone.
  5. 5Fold the fabric over the top like a burrito wrap and cover with soil or turf.

Comprehensive Practical Guide

In-depth analysis, domain guidelines, standard practices, and common pitfalls.

Why Non-Woven Geotextile Fabric Is Vital for Drainage

Without non-woven geotextile filter fabric surrounding the gravel trench ("burrito wrap"), fine silt and clay soil migrate into the stone voids, completely clogging the drain within 2 to 5 years.

How Much Slope Does a French Drain Need?

A French drain needs at least a 1% fall — 1 inch of drop per 8 feet of run — so water flows to the outlet instead of sitting in the pipe. On a 50 ft run that is about 6 inches of fall from start to finish. Discharge to daylight downhill, a dry well, or a storm drain where local rules allow — never onto a neighbour's land.

Frequently Asked Questions About French Drain Calculator

Direct, verified answers to common calculation and methodology questions.

Holes must ALWAYS face DOWN. Water enters from the bottom as the water table rises and drains away before saturating the ground above.
Authoritative Sources & Data References:
  • American Society of Civil Engineers (ASCE) Urban Drainage Design Guidelines

Disclaimer: Maintain a minimum 1% slope (1 inch drop per 8 feet) toward a safe discharge exit.