Automotive & FitnessLast reviewed: November 2026

Bicycle Gear Ratio Calculator

A 50-tooth chainring with an 11-tooth cog on a 700c wheel gives 119.5 gear inches and 51.5 km/h at 90 rpm. Enter your chainring, cog, wheel size and cadence, and the calculator works out the ratio, gear inches, development per pedal turn, speed and gain ratio, with the full cassette table.

Key facts:
  • Gear ratio is chainring teeth divided by cog teeth.
  • A 50 × 11 gear on a 700c wheel is 119.5 gear inches.
  • Development is the distance rolled per pedal turn, in metres.
  • Most riders are fastest at a cadence of 80–100 rpm.
  • Gain ratio lets you compare gears across different wheel sizes.

Loading calculator…

Share or Export Current Results

Share Bicycle Gear Ratio Calculator directly or copy link to clipboard

TwitterLinkedInFacebookWhatsApp

Calculation Formula & Mathematical Engine

Theoretical equation governing this computation.

Ratio = \frac{Chainring}{Cog}, \quad GearInches = Ratio \times WheelDiameter, \quad Speed = Development \times Cadence \times \frac{60}{1000}

Variable Definitions

RatioChainring teeth divided by cog teeth (for example 50 ÷ 11 = 4.545)
GearInchesRatio times wheel diameter in inches — the size of the wheel this gear feels like
DevelopmentDistance the bike rolls per pedal turn, in metres (gear inches × π × 0.0254)
CadencePedal speed in revolutions per minute
GainRatioRatio adjusted for crank length and wheel radius — the fair way to compare bikes with different wheels

Step-by-Step Calculation Example

Speed of a 50 × 11 Gear on a 700c Wheel at 90 rpm

Scenario: A road rider in the top gear (50-tooth chainring, 11-tooth cog, 700c wheels) pedals at 90 rpm on flat ground.
Gearing50T chainring × 11T cog
Wheel700c (26.3 in diameter)
Cadence90 rpm
Execution Steps
  1. 1Gear ratio: 50 ÷ 11 = 4.545
  2. 2Gear inches: 4.545 × 26.3 = 119.5 in
  3. 3Development: 119.5 × π × 0.0254 = 9.54 m per pedal turn
  4. 4Speed: 9.54 × 90 × 60 ÷ 1000 = 51.5 km/h (32 mph)
  5. 5Gain ratio: 4.545 × (172.5 ÷ 334) = 2.35
Final Verified Output:51.5 km/h at 90 rpm | 119.5 Gear Inches | 9.54 m Development

Comprehensive Practical Guide

In-depth analysis, domain guidelines, standard practices, and common pitfalls.

What Is a Good Gear Ratio for Climbing?

For steep climbs you want a low gear: a 34-tooth chainring with a 32-tooth cog gives a ratio of 1.06 and about 28 gear inches on a 700c wheel, so each pedal turn moves you about 2.2 metres. Racers use 34 × 28 or easier; loaded touring bikes go lower still. If your easiest gear still hurts on hills, fit a bigger cassette cog before you change the chainring.

What Are Gear Inches and Development?

Gear inches is the old way to compare gears: it is the diameter of the wheel your gear feels like. Development is the modern version — how far the bike rolls per pedal turn. A 50 × 11 gear rolls 9.54 metres per turn, while a 50 × 32 gear rolls 3.28 metres. Multiply development by cadence to get speed.

What Cadence Should I Ride At?

Most riders are fastest at 80–100 rpm. Below 70 rpm you push hard on the knees; above 110 rpm most riders bounce in the saddle. Use the calculator to see your speed at different cadences: the same gear at 90 rpm is much faster than at 70 rpm, so spinning faster is often better than pushing a bigger gear.

Frequently Asked Questions About Bicycle Gear Ratio Calculator

Direct, verified answers to common calculation and methodology questions.

Divide the chainring teeth by the cog teeth. A 50-tooth chainring with an 11-tooth cog gives 50 ÷ 11 = 4.545. Multiply by the wheel diameter for gear inches, and by cadence for speed.
Authoritative Sources & Data References:
  • Sheldon Brown — Bicycle Gear Calculator
  • Park Tool — Gear Ratio Guidance

Disclaimer: Speeds assume a steady cadence on flat ground with no slipping. Wind, hills, tyre pressure and rider weight change real speed.